Some proposals simply say to paint the walls and ceiling and never specify the number of coats to be applied. If the colors are similar enough, it's possible to get away with one coat of paint and not discount your pricing. No matter how hard you try, tiny, pin-sized air holes will pop exposing the original walls. This may not bother you if you can't notice it, but principally speaking you should have paid your painter less for the work.
Keep an eye on the new cans as they're being brought in. Make sure they look new and don't have paint in the rim of the can. If it's a five-gallon bucket, check to see whether the lid is still sealed on with the plastic strip. The only time it's acceptable to mix water in the paint is when you're using a deep or ultra deep base paint to reduce its stickiness, which is rare with new paint technology. Dark primary colors are composed almost entirely of tint that makes it very hard to work with without adding water.
Husky's Heavy Duty 45-Degree Flaring Tool Set creates Husky's Heavy Duty 45-Degree Flaring Tool Set creates precision flares in copper brass and aluminum tubing from 3/16 in. to 5/8 in. O.D. The feed screw design provides smooth and easy operation. Simply use a screwdriver or lever to tighten the wingnuts as tight as possible when making flares to ... More + Product Details Close
I disagree with your criteria to hire a painter. A prompt returned call is nice but does not indicate the quality or fairness of the painter. As far as a written estimate, that should be more of a qualifier for the bid versus an evaluation criterion. I'm not sure one would have favorable results by hiring a painter on this basis. As far as the bidding process, change orders should ONLY be used if the customer requests additional scope (PMP 101). Angie's list should consider asking reviewers if/how much they were told to pay compared with the estimate. Unfortunately, there are a lot of contractors that are unethical and need to be accountable.
Over the past year I have had several jobs given to 2 Angie's list recommendations and 1 not from a recommendation. They all have one thing in common, lack of sufficient and correct preparation to save time, labor, and the fact that they put a person in charge that was a cut corners type of worker. The two from Angie's list sent worker/s back to try touch up problems, but once the job is not prepared correctly in the first place any extra work is like putting a band-aid on a dirty wound.
So why not just paint your own home. I'm not a painter, so my wife and I take our time, buying the paint and supplies, and doing our own painting. Yes, we need to tape, and it's not perfect, but we get the satisfaction of seeing our completed work. Get the supplies, sliders for your furniture, and patience and go for it. That way YOU have control over the entire project.
In this Jan. 11, 2004 file photo former Congressman Ron Dellums gives a speech during a celebration honoring slain civil rights leader Dr. Martin Luther King Jr. in Oakland, Calif. Dellums, a fiery anti-war activist who championed social justice as Northern California's first black congressman, has died at age 82. Longtime adviser Dan Lindheim says Dellums died early Monday, July 30, 2018, at his home in Washington, D.C., of cancer. Nick Lammers, East Bay Times via AP
When you refinish your existing cabinet doors, you get a whole new look without the astronomical costs normally associated with a kitchen remodel. It’s a much smarter way to update your space, especially if your cabinets are still in good condition. It doesn’t make sense to throw out perfectly good materials, just because you’re tired of the color.
To paint a large section without leaving lap marks, roll the nearly dry roller in different directions along the dry edge, feathering out the paint as you go. After completing the entire length of the wall or ceiling, move to the next section and paint over the feathered edges. For the second coat, apply the paint in the opposite direction. This crisscrossing paint application sharply reduces (if not eliminates) lap marks.
I really enjoyed this first book of the House of Comarre series. The heroine Chrysabelle is a comarre, which is described as a geisha for vampires. Her patron ends up dead and she goes on the run to avoid being blamed for it. She ends up meeting the other main characters Mal, Doc, and Fi after her escape. This story has all the usual supernatural elements like vampires, Fae, and shapeshifters but they aren't used in a generic way. The Fae in particular have some unique characteristics, and the hidden vampire society that Chrysabelle lived all her life in creates an enigmatic and fascinating background, and at times setting, for the story. Mal has a tragic backstory that gets revealed over time, and the way his, chrysabelle's, Fi's, and Doc's lives are (and become) connected will surprise you and is fascinating to read about. The evolving relationships between these four are really at the heart of the story and are what makes it so good.
This is so much different than Kristen’s other work. She’s one of my favorite authors. I had read House Of The Rising Sun before this one and was told that that trilogy would be enjoyed even more, hard to get any better than it was, if I read this Comarre series first. They tie in together but don’t have to be read in order. This first book has a lot of telling but I feel like that is necessary because this is a big world so it needs that world building. I loved all the main characters. I really liked the uniqueness of Crysabell (spelling?) needing to be bled or have a vampire feed from her or she would be like blood drunk. It’s her purpose to feed her vampire.
As a former professional painter, something that drives me crazy is when I see painters cut in around wall plates. First of all, the amount of time that it takes to cut in is usually much longer than the amount of time that it takes to simply remove the wall plate. Secondly it does not look nearly as clean as it does when the wall plate is removed and thirdly it can invariably leave paint on the wall plate itself which also looks sloppy. Make sure the painter takes them off and then reinstalls them. It's less time.