Most painters have no problem painting doors in place, but they recommend you lay the door on sawhorses and work horizontally. If you have a paneled door, start with the panels and work from the outside edges in toward the center. "Watch the corners — paint loves to puddle," warns Dixon. While the paint is still wet, lightly "tip off" the panel with an almost dry brush. (Tipping off is pulling the brush over the surface to level out the finish.) When painting the stiles (vertical) and rails (horizontal) just follow the grain of the wood. When the grain changes abruptly, for instance, where the rail meets the stile, don't stop your brush stroke — you'll only leave a lump of paint. Apply paint across the joint with a full stroke, and then tip off the overlapping section by pulling the brush in the direction of the grain. "Make sure the door is dry before painting the opposite side or rehanging it," says Maceyunas.
Residential house painters on the Handy platform have used countless gallons of paint and tons of brushes over the years. With a wealth of experience under their belts, they know the best, quickest and most cost-effective ways to get the work done. From how to achieve that perfect glossy finish to ensuring no paint drips onto your crown molding, you might find yourself picking up a few tips!
A good paintbrush is key to a professional-looking finish. "A quality brush costs $15 to $25, but you'll discover that pros aren't as talented as you thought," says Doherty. "The equipment has a lot to do with their success." Most of our pros prefer natural-bristle brushes for oil-based paints, but they recommend synthetics for all-around use. When choosing a brush, pay attention to the bristles. Synthetic brushes are made of nylon or polyester, or a combination of the two. Poly bristles are stiffer, which makes them good for exterior or textured work, but for fine interior work, Doherty uses softer nylon brushes. Look also for tapered bristles, which can help you work to an edge, and flagged tips, which help spread the finish smoothly and evenly. Brushes are available in 1- to 4-inch widths. Most painters keep an arsenal on hand to match the job. "Use common sense," says Maceyunas. "A smaller brush gives you more control, but no one wants to paint a door with a 1-inch-wide brush." Doherty recommends starting with a 2- or 2-1/2-inch sash brush. The angled brush makes it easier to cut to a line and puts more bristles on the work than a square-tipped brush.
To solidify this response, we have been in business for over 30 years as a painting contractor. We didn't just paint a couple of houses 25 or 30 years ago, we paint approximately 900-1000 painting jobs per year and operate with 40 professional painters doing commercial, residential and industrial painting. This article on behalf of Angie's List is totally asinine! I was under the impression Angie's List was only carrying "legitimate" contractors with established reputations. This article written is primarily referring to bottom feeding, one man band operations, trying to hustle for a paycheck.
In England, little is known of the trade and its structures before the late 13th century, at which paint guilds began to form, amongst them the Painters Company and the Stainers Company. These two guilds eventually merged with the consent of the Lord Mayor of the City of London in 1502, forming the Worshipful Company of Painter-Stainers. The guild standardised the craft and acted as a protector of the trade secrets. In 1599, the guild asked Parliament for protection, which was eventually granted in a bill of 1606, which granted the trade protection from outside competition such as plasterers.
"Cutting in is an acquired skill, but it's something you can't do at all with a ratty brush," says Doherty. When cutting in on a wall, he loads his brush and spreads out the excess paint, then works the brush up to the line between wall and ceiling. A brush stroke that's too wide creates a hatband, or smooth brushed band, on the very top of the wall where it meets the ceiling. To avoid this, Dixon recommends rolling first and then cutting in with a brush. "A good roller can get within 1/2 inch of the ceiling," he says. "You'll save time by not brushing more then you have to." When painting baseboards, "a wide taping knife makes a good paint guard," says Span. "Just keep the blade clean to prevent drips from working around the edge of the knife."
I am very satisfied with the job that was done by this company (exterior painting of two-story house). The price was very reasonable. All crew members are very professional, polite, punctual, and always cleaned the place at the end of the day. They did a very thorough preparation before painting and their painting work was exceptional. I am happy to have my house painted by this company. It looks nice, clear, and we have many positive feedback from our neighbors on this work that was done by this company. I highly recommend this company for any painting work.
A thorough scrubbing is a must before painting any exterior surface. It removes the dirt and broken-down paint residues that keep fresh coats from adhering and gets rid of mildew that grows on paint in all but the most arid climates. Most contractors clean with pressure washers, but in the hands of someone unfamiliar with the equipment, these can gouge wood, shatter glass, and drive water behind siding and trim. Using a hose, a pump sprayer, and a scrub brush is slower but safer, and just as effective.
When planning for a project, we take into consideration key factors such as the underlying surface and the exposure to wear from weather and other environmental factors. For these reasons, particularly for Melbourne house painters, choosing the right type of paint can make a huge difference on your investment, how long it lasts, and how good it looks when the work is finished.That is why we take great care to understand our customer’s needs as well as the building specifications, to ensure that we give you an accurate quote with assurance that your investment is optimized.